SQ Automatic Recloser

Combine a three-phase vacuum switching unit with electronic protection and reclosing control for distribution automation. Select the SQ voltage version and confirm the controller functions, auxiliary supply and network interfaces as one coordinated package.

SQ SERIES VACUUM SWITCHING WITH ELECTRONIC CONTROL

SQ Automatic Recloser

Combine a three-phase vacuum switching unit with electronic protection and reclosing control for distribution automation. Select the SQ voltage version and confirm the controller functions, auxiliary supply and network interfaces as one coordinated package.

Voltage versions
15.5 / 22(24) / 33(38) kV
Rated current
800 A
Short-circuit breaking
16 kA
Interruption medium
Vacuum
OVERVIEW

Vacuum switching with reclosing control

The SQ assembly pairs a three-phase vacuum switching unit with electronic protection and reclosing control. Select one voltage version and confirm the switching unit, controller and auxiliary power as a coordinated package. The controller configuration defines protection settings, reclosing sequence, lockout behavior and remote interfaces. These functions need to match the feeder coordination study.

TECHNICAL DATA

SQ technical specifications.

Electrical ratings

SQ electrical ratings
Electrical parameterSpecification
Model familySQ automatic recloser
Voltage version designations15.5 kV; 22(24) kV; 33(38) kV
Rated current800 A
Rated short-circuit breaking current16 kA
Rated short-time withstand current16 kA; confirm duration for the selected version
Lightning impulse levels110 / 150 / 200 kV for the respective listed versions
One-minute power-frequency withstand50 / 60 / 70 kV for the respective listed versions
Rated frequencyConfirm the selected 50 or 60 Hz version
Controller selectionHLC6130 configuration to be agreed with the switching unit

Confirm the selected assembly, component ratings and verification documents. Family options do not describe every supplied configuration.

Configuration options

Match the equipment configuration to the circuit duty and installation interfaces.

SQ functional-unit options
Selection itemSpecification / requirement
Switching unitSelect voltage version, insulation level and mounting arrangement
Protection and reclosing controlDefine enabled functions, settings, sequence and lockout requirements
HLC6130 controllerConfirm the selected hardware, firmware and required control functions
Auxiliary supplyDefine control power, charging and backup requirements
CommunicationsSpecify the actual protocol, port and remote-control requirements

Confirm the selected order code and component schedule before approval.

Protection & operation

Protection coordination

Provide the feeder study and upstream/downstream protective-device information before setting the control.

Reclosing policy

Specify the permitted sequence, dead times, lockout conditions and remote-control policy for the utility.

Measurement and signals

Agree required measurements, status signals, alarms and control interfaces.

Commissioning

Verify the supplied hardware, settings and functional tests against the approved project procedure.

Functional overview only. Qualified personnel must follow the approved isolation procedures and supplied operating instructions.

Define the equipment configuration.

Define the equipment duty and interfaces before requesting the project configuration.

SQ configuration requirements
Configuration itemPurposeDefine for your project
Vacuum switching unitSwitch load and interrupt the specified fault dutyVoltage version, current and fault level
Protection and reclosingApply the approved feeder operating policyFunctions, settings, sequence and lockout
Controller and powerOperate and monitor the unitHardware, auxiliary supply and backup
Remote interfaceConnect the selected automation systemProtocol, physical interface and signal list
Mounting packageFit the installation structurePole details, brackets and cable lengths

Final components and scope of supply are defined in the project quotation.

Dimensions & interfaces

SQ cabinet dimensions
InterfaceReference / requirementSelection note
Pole mountingProject-specific bracket and support arrangementProvide pole and installation details
Primary terminalsConfirm terminal orientation and conductor connectionCoordinate phase clearances and loading
Controller enclosureConfirm mounting, access and cable entryProvide control-box location
Interconnection cableSelect cable type, length and connectorsCoordinate switch-to-controller routing
Maintenance spaceAllow access to mechanism, controller and connectionsApprove the installation drawing

Use the approved project drawing for dimensions, clearances, foundations and connections.

Installation

Network information

Provide system voltage, frequency, fault level, earthing arrangement and feeder duty.

Mechanical design

Approve pole attachment, terminal connections, clearances and support loads.

Control package

Check the auxiliary supply, backup requirements, interconnection and communication equipment.

Technical records

Request corrected configuration-specific ratings, dimensions, control documentation and test records.

Site conditions

SQ site conditions
ConditionRequirement / project input
Installation dutyDistribution-feeder switching and automation
Site conditionsState altitude, temperature, pollution and wind or ice exposure
Enclosure protectionConfirm separately for the switching unit and controller
Electrical environmentProvide insulation and surge-protection requirements
Control environmentConfirm supply quality, backup duration and communications

Provide any conditions outside the stated range before ordering. Final suitability requires project-specific confirmation.

APPLICATIONS

Where SQ is used

Distribution feeder protection

Match interruption and withstand duty to the network, then coordinate the selected protection and reclosing settings.

Distribution automation

Specify remote commands, status signals, measurements and communications for the selected controller hardware and firmware.

PLANNING EXAMPLE

Planning a recloser-controlled feeder

Planning example: a feeder needs electronic protection and a utility-defined reclosing sequence. The switching unit and controller are approved together.

Select the voltage version

Provide system voltage, current, fault level and insulation requirements for one SQ version.

Define protection and reclosing

Provide the coordination study, permitted sequence, dead times and lockout conditions.

Agree control interfaces

Confirm auxiliary power, controller hardware and firmware, communications and the required functional tests.

MANUFACTURING & SUPPORT

Production, OEM and quality control

01 / PRODUCTION

Manufacturing

Production follows the approved drawings, the applicable product standards and the agreed inspection plan.

02 / CUSTOMIZATION

OEM & ODM

We can adjust the configuration for your operating environment and provide neutral packaging or your logo. Send the site conditions and branding requirements with your enquiry.

03 / QUALITY

Quality control

Incoming components, production work and finished units are checked against the requirements for the ordered configuration.

Inspection before dispatch

Material inspection

Incoming materials and components are checked against the approved specifications before production.

In-process checks

Assemblies and semi-finished components are inspected at the relevant production stages.

Final inspection

Finished equipment and release records are checked against the approved order requirements.

Factory acceptance testing (FAT). Every unit undergoes FAT before packing. Test items and acceptance criteria follow the product and approved configuration. FAT reports and packing inspection photos accompany the shipment. Factory attendance, video witnessing or independent inspection can be arranged with an agreed scope and schedule.

FURTHER READING

Related articles

Explore related guides for product selection, specifications and project planning.

Review interruption steps, main components and protection roles.

Frequently asked questions

The quotation must identify the switch body, controller, interconnection cable, mounting parts and accessories. Confirm the complete package before order.

HLC6130 is the documented control option. Confirm the required version, functions, interfaces and compatibility with the selected switching unit.

No. Specify the required protocol and interface; confirm the actual controller hardware and configuration in the quotation.

Both require a corrected configuration-specific schedule. They are not assigned as universal values on this page.

Send voltage, frequency, fault level, protection study, reclosing policy, control-power requirements, communication specification and installation details.